Search Results

Search results 1-20 of 42.

  • Dot2 wont recognize my node

    TVTM_Brian - - the dot2 Forum

    Post

    Neither ArtNet nor sACN require the use of the entire Class A. Both ArtNet and sACN CAN be ran on less than an entire Class A. Yes, the ArtNet node doesn't need to be set to Universe 00/Subnet 00, but there is NO requirement to use a full Class A subnet that I am aware of. I, personally, will never use to 2.x.y.z Class A subnet as that IP range is actually assigned to routable networks. 10.x.y.z is specifically reserved for local networks.

  • Dot2 wont recognize my node

    TVTM_Brian - - the dot2 Forum

    Post

    The eDMX1-PRO also works great if/when you upgrade to grandMA2/3!

  • Dot2 wont recognize my node

    TVTM_Brian - - the dot2 Forum

    Post

    IPv4 should work just fine, but I would recommend staying away from generic/no label hardware as you never know what you're getting and support for such hardware may be little to none. The Enttec node I got (eDMX1-PRO) only cost about $130 USD and has worked flawlessly, with manufacturer support and several firmware updates since new. At the time the cost was a lot for me, but quickly became one of the best purchases I made.

  • Dot2 wont recognize my node

    TVTM_Brian - - the dot2 Forum

    Post

    The IP shown under ArtNet SHOULD be your computers IP. What ArtNet node do you have? Mfgr & model...

  • Dot2 wont recognize my node

    TVTM_Brian - - the dot2 Forum

    Post

    dot2 won't show your ArtNet node in the Sessions screen, it just sends out the data for anyone to see, so to speak. Even in grandMA2, ArtNet/sACN nodes will not show up in the network protocols screen.

  • Dot2 wont recognize my node

    TVTM_Brian - - the dot2 Forum

    Post

    Could be a subnet issue as your computer is set to 10.0.0.1 and the node is at 10.100.60.200. Try changing the nodes IP to something in the same Class C, such as: 10.0.0.200 Also, check that your Subnet Mask is set properly(e.g. 255.255.255.x) dot2 and grandMA2 work great in the 10.x.x.x range with both ArtNet, sACN & MA Net. I've been running this IP range for years without any issue using four class C's (10.0.0.1-10.0.3.255) and a subnet mask of 255.255.252.0 I gave myself four class C's so I'…

  • show dot2 + GM2 show on GM2

    TVTM_Brian - - the dot2 Forum

    Post

    dot2 showfiles can be opened and read by grandMA2, but not the other way around. I would load your dot2 show into the grandMA2, then Partial Show Read the patch from their gMA2 showfile. Presets and effects can also be brought in via PSR... Click here(open in new window)

  • Chase in white

    TVTM_Brian - - the dot2 Forum

    Post

    Looks like you'll need to make a "chaser"(aka, manually build the effect) to get what you're looking for. dot2's predefined effects are limited in that we can't select presets as high/low values. (Wish list?) The way I tested what you were looking for was incorrectly done, so please ignore my first post.

  • Chase in white

    TVTM_Brian - - the dot2 Forum

    Post

    My reply was done ALL in the programmer... LoL

  • Chase in white

    TVTM_Brian - - the dot2 Forum

    Post

    Two color chase effect should do what you're looking for. Low value set to "off" on all colors High value set to white

  • Dot2 onPC, Bome and APC20

    TVTM_Brian - - the dot2 Forum

    Post

    In Bome, you need to have one "preset" per device, and ONLY listen to that device in each preset.

  • Michael, I think he meant multi-touch support from within the onPC software, correct me if I'm wrong. I too already have a multi-touch capable monitor but can't do more than a single touch point due to the software.

  • 1) Click/Press the Macro button 2) Select "Export Patch to USB" 3) Save the patch file(xml) 4) Open the patch file in Firefox (or other xml worthy program) 5) File, Print, done...

  • Chauvet Circus 2.0 IRC

    TVTM_Brian - - the dot2 Forum

    Post

    Disregard, figured it out... Program --> Color--> Raw: ColorMix--> ColorMix Speed --> Color--> Raw: ColorMix --> ColorMixMacroRate Pod Strobe Speed --> Beam --> Raw: Shutter --> Shutter SMD Strobe Speed --> Beam --> Raw: Shutter --> Shutter2

  • Chauvet Circus 2.0 IRC

    TVTM_Brian - - the dot2 Forum

    Post

    Anyone had any luck with this profile? I have a client with one of these lights and the default MA profile isn't doing much of anything. Thanks!

  • web ma-dot2, accessories

    TVTM_Brian - - the dot2 Forum

    Post

    The item you found does not appear to be an official MA product. Nor would it actually work for the dot2 node as pictured, as it blocks the IEC power connector and switch.

  • That's the same one I use for DMX output, it has an option to act as an input as well. You would need one for output and a second one for input.

  • As always Micheal, you guys are the best! I was able to export and update the fixture profile!

  • By default, MA has the highlight value on RGB fixtures set to max for each color, is there any way to change the default to 0?

  • dot2 onPC

    TVTM_Brian - - the dot2 Forum

    Post

    I use an Akai APC40 (original, NOT mk2) and love it! Anywhere between $100-250 USD on eBay right now...